SportDOG Add-A Beeper Accessory

Directions:
Prepare the Add-A-Beeper
Insert the Battery
1. Remove the battery cover.
2. Insert the CR-123 3-volt lithium battery with the positive (+) end facing outward.
3. Replace the battery cover.

To Turn the Add-A-Beeper On/Off
To Turn the Add-A-Beeper On:
1. Press and hold the On/Off Button until the Add-A-Beeper's Indicator Light comes on and the Add-A-Beeper beeps 1 time.
2. Release the On/Off Button.
The Add-A-Beeper's Indicator Light will flash until the Add-A-Beeper is turned off.
The flashing light indicates the Add-A-Beeper is ready to receive a radio signal from the Remote Transmitter.

To Turn the Add-A-Beeper Off:
1. Press and hold the On/Off Button until the Add-A-Beeper's Indicator Light comes on and the Add-A-Beeper beeps 2 times.
2. Release the On/Off Button.
Note: The Add-A-Beeper will provide approximately 100 hours of "on" time depending on how frequently the beeper function is activated and depending on which Tone Mode the Add-A-Beeper is set to.

Beeper Indicator Light

Add-A-Beeper Function	Indicator Light Response
Add-A-Beeper On-Good Battery	Flashes twice every second
Add-A-Beeper On - Low Battery	Flashes once every second

Reset the Add-A-Beeper
To reset the Add-A-Beeper to work with a new Remote Transmitter or to reprogram a new Add-A-Beeper to work with your existing Remote Transmitter:

A. Turn the Add-A-Beeper off.

B. Press and hold the On/Off Button. The Add-A-Beeper's Indicator Light will come on, then turn off after 4-5 seconds. If the On/Off Button is released too early, the Add-A-Beeper's Indicator Light will begin flashing as normal. If this occurs, start over and repeat from A.

C. After the Add-A-Beeper's Indicator Light has turned off, release the On/Off Button.

D. Press and hold the Locate Button for the UplandHunter Transmitter or the Tone Only Button on all other Remote Transmitters (except SD-3200) until the Add-A-Beeper's Indicator Light flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once the Add-A-Beeper's Indicator Light has flashed 5 times, the Add-A-Beeper has been reset and will begin flashing as normal. If the Add-A-Beeper's Indicator Light does not flash 5 times, start over and repeat from A.

Program the Add-A-Beeper
To Set the Tone:
1.Reset the Add-A-Beeper
2. Turn the Add-A-Beeper off.
3. Press and hold the ON/OFF button. After 8 seconds, the Add-A-Beeper will start to emit the different tones. For a list of tones, refer to the chart below.
4. Continue holding the ON/OFF button until the desired tone is emitted. Release the ON/OFF button.

TONE
1	Low Volume Hawk
2	High Volume Hawk
3	Bobwhite Quail Call
4	Triple Beep
5	Low Volume Beep
6	High Volume Beep
7	Double High Volume Beep
8	High Falling to Low Volume
9	Double High Falling to Low Volume

To Set the Run Mode:
To program the Run Mode, press the ON/OFF button again within 2 seconds of programming the Tone. The Add-A-Beeper will emit a single beep for Mode 1, a double beep for Mode 2, and a triple beep for Mode 3. When the desired mode is heard, release the ON/OFF button. The unit will then go into normal operating mode and the LED will blink every second.

Mode 1	Silent	No Beep when dog is running/ Beeps once per second when dog is on point.
Mode 2	5 Second	Beeps every 5 seconds when dog is running/Beeps once per second when dog is on point.
Mode 3	10 Second	Beeps every 10 seconds when dog is running/Beeps once per second when dog is on point.

Fit the Add-A-Beeper to Your Dog
This system is designed so you can add or remove the Add-A-Beeper to or from the collar strap as needed.

To Place the Add-A-Beeper on the Collar Strap:
1. Press the green rubber saddle into the opening at the bottom of the beeper.
2. Thread the end of the collar strap through the slot in the beeper. Continue sliding it through the slot in the saddle and then through the slots on the opposite side of the saddle and beeper.
3. Slide the saddle and Add-A-Beeper a few more inches up the Collar Strap.
Note: The saddle creates a very snug fit for the Add-A-Beeper. This snug fit is intentional to keep the Add-A-Beeper from sliding on the strap.

To Place the Entire System on Your Dog:
1. With your dog standing, place the Collar Strap around the narrowest part of your dog's neck.
2. Ideally, the Collar Receiver should be centered at the front of the dog's neck and the Add-A-Beeper should be centered behind the dog's head. Slide the Add-A-Beeper as needed to position it properly.
3. The Collar Strap should fit snugly, yet be loose enough to allow one finger to fit between the strap and your dog's neck.
4. Allow your dog to wear the collar for several minutes, and then recheck the fit.
Note: The Add-A-Beeper can be used on the collar strap without the Collar Receiver. To remove the Collar Receiver, simply slide the saddle and Add-A-Beeper off the strap, and then do the same with the Collar Receiver. Replace the saddle and Add-A-Beeper. The Add-A-Beeper, without the Collar Receiver, may shift due to movement.