1. Home > 
  2. Dog Supplies > 
  3. Grooming Supplies > 
  4. Hair Trimmers & Scissors > 
  5. Andis® Electric Clippers > 
  6. Andis ProClip AG2 Pet Clipper


Andis ProClip AG2 Pet Clipper

Item: 22215
1. Select product:


Andis Plus AG 2-Speed This company makes exceptional products that will not let you down. This clipper is made for very quick cutting, so if you want pet grooming to be less time-consuming, this is for you. Additionally, the motor does not require maintenance, the clipper is surprisingly quiet, and detachable blades work great. Everything about this clipper makes the process of giving your furry friend a hair cut easier. The contours and durability of the housing make it simple to hold and hard to break.

  • Fast, quiet, and very efficient operation
  • Saves time and does not require much maintenance
  • Housing makes it easy to hold and difficult to break
  • Useful Information

    IMPORTANT SAFEGUARDS: When using an electrical appliance, basic precautions should always be followed, including: Red all instructions before using the Andis Clipper.

      DANGER: To reduce the risk of electric shock:
      1. Do not reach for an appliance that has fallen into water. Unplug immediately.
      2. Do not use while bathing or in a shower.
      3. Do not place or stor appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
      4. Always unplug this appliance from the electrical outlet immediately after using.
      5. Unplug this appliance before cleaning, removing or assembling parts.

      WARNING: To reduce the risk of burns, fire electric shock, or injury to persons:
      1. An appliance should never be left unattended when plugged in.
      2. Close supervision is necessary when this appliance is used by, on or near children or individuals with certain disabilities.
      3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Andis.
      4. Never operate this appliance if it has been dropped or damaged, or dropped into water. Return the appliance to an Andis Authorized Service Station for examination and repair.
      5. Keep the cord away from heated surfaces.
      6. Never drop or insert any object into any opening.
      7. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
      8. Do not us ethis appliance with a damaged or broken blade or comb, as injury to the skin may occur.
      9. To disconnect turn control to "off" then remove plug from outlet.
      10. WARNING: During use, do not place or leave appliance where it may be (1) damaged by an animal or (2) exposed to the weather.

    To reduce the risk of electric shock, this appliance has a polarized plug (one balde is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electricisan to install the proper outlet. Do not change the plg in any way.

    Before starting clipper, remove blade fuard (some models may not have a blade guard). Plug cord into electrical outlet, operate 120 volt, 60 cycle AC electrical current or as noted on the unit. To start clipper, move switch button to ON position. To stop clipper, move switch button back to original position. After using your clipper, rewrap cord and store in a safe place.

    Your clipper comes with normal and high speed operation. Use the normal setting (Setting #1) for most cutting needs. Use the high speed setting (Setting #2) for cutting through heavy coats.

    To remove blade set, first make sure your clipper is switched OFF and UNPLUGGED. Push down on blade, then gently pull the blade forward, and slide it off the blade hinge. If your blade hinge should snap closed and is flush with the clipper, use a small standard screwdriver to pry the tongue of the hinge out.

    NOTE: Hair may accumulate in the front cavity of the housing under the blade. Ig this happens, you can clean out the hair by brushing out the cavity with s small brush or an old toothbrush while the blade is off the clipper.

    To replace or change your blade set, slide the blade bracket onto the hinge of the clipper and with the clipper turned ON, push the blade twards the clipper to lock into position.

    Due to the high speed nature of Andis clippers, please check for blade heat often, especially on close cutting blades. If blades are too hot, dip the blades only into Andis Blade Care Plus or apply Andis Cool Care Plus and then Andis Cliper Oil. If you have a detachable balde unit, you can change your balde in order to maintain a comfortable temperature; using multiple blades of the same size is popular among groomers.

    Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow down, it's a sure sign blades need oil. Place a few drop of Andis Clipper Oil on the front and side of the cutter blades. Wipe exceee oil off blades with a soft dry cloth. Spray lubricants contain insufficient oil for good lubrication, but are an excellent clipper blade coolant. Alway replace broken or nicked blades to prevent injury. You can clean the excess hair from your blades by using a small brush or worn out tooth brush. To clean the blades we suggest to immerse the blades only into a shallow pan of Andis Clipper Oil, while the clipper is running. Any excess hair and dirt that has accumulated between the blades should come out. After cleaning, turn your clipper OFF and dry blades with a dry cloth and start clipping again.

    If upon cleaning your blades you find that the blades will still not cut, there may be a few fibe pieces of hair trapped between the upper and lower blade. If this happens, you will need to snap the blade off the clipper. Proceed to slide the upper blade to one side, without loosening the tension spring or moving the upper blade completely out from under the tension spring. Wipe the surface between the blades clean with a dry cloth, then place a drop of clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring. Now slide the upper blade to the opposite side of the lower blade and repeat this process. After completing this procedure, slide the upper blade, centering it over the lower blade. Handle or store your Andis Clipper with the blades down so excess oil will not run into the clipper case.

    If you clipper blades no longer cut properly (be sure to try more than one blade, since the blade currently being used may be dull), it could be that your blade drive assembly needs replacement.

      TO CHANGE THE BLADE DRIVE ASSEMBLY: 1. Remove blade set.
      2. Remove drive cap.
      3. Remove blade drive mounting screws
      4. NOTE: Before removing blade drive assembly, note the way it is positioned (this will help you in reassembly). Remoce blade drive assembly.
      5. Drive bearing should be at its lowest position, if not, move it with your finger to lowest position.
      6. Put on new drive assembly, align screw holes and press down.
      7. Reassemble blade drive by mounting screws.
      8. Replace drive cap.
      9. Replace blade.

    WARNING: Clipper must be unplugged before removing carbon brush caps or performing any maintenance, as electrical shock may occur. The carbon brushes of your clipper shold be checked every three to six months. Carbon brush replacement should be performed when the carbon brushes reach no less than 1/16" in length. To replace the carbon brushes, unscrew brush caps with a standard screwdriver. Do one side at a time.

    CAUTION: The carbon brushes are spring loaded. Take precaution when unscrewing the brush caps from the unit. The brush spring should be in plain view upon removing the cap. Pull out the spring and brush from its canal, then remove old carbon brush. Tip the clipper to one side so the carbon brush slides out. Be sure to note the way the brush is inserted so that if it does not need replacing, it may be re-inserted in exactly the same position. When placing a new carbon brush into the carbon brush canal, make sure to align the curvature on the end of the carbon brush with the curve of the commutator seen at the bottom of the canal. When aligned properly, the two beveled edges of the carbon brush will be located in the upper right and lower left corners. Be perform this procedure correctly may cause the carbon brushes to not seat themselves properly against the commutator. Replace the carbon brush spring into the brush cavity after the carbon brush has been installed, then replace carbon brush cap with a standard size screwdriver. Turn clockwise only until you feel the brush cap stop. If the brush cap is tightened too tightly, it will force the brush spring past the carbon brush and will cause damage to the commutator.

    Customer Reviews

    Questions and Answers

    1 Question & 0 Answers
    from AUSTIN, TX asked:
    September 30, 2015
    what is the difference between this clipper and Pro clip ultra edge?

    Andis UltraEdge AGC Super 2-Speed Pet Clipper - MaroonAndis UltraEdge AGC Super 2-Speed Pet Clipper - MaroonReg price: $207.99
    Sale price: $169.99
    Andis UltraEdge AGC Super 2-Speed Pet Clipper - BlueAndis UltraEdge AGC Super 2-Speed Pet Clipper - BlueReg price: $207.99
    Sale price: $159.95
    Andis TCX All-In-One Clipper/TrimmerAndis TCX All-In-One Clipper/TrimmerReg price: $77.99
    Sale price: $59.99
    Andis AGC 2- Speed Clipper with #10 BladeAndis AGC 2- Speed Clipper with #10 BladeReg price: $324.99
    Sale price: $249.99
    CALL IN YOUR ORDER 800.889.8967

    Stay in touch. Friends fur-ever!

    Terms and Conditions

    You have to agree on terms in order to proceed to the subscription.